Technical Accessories

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Robust, solid construction

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

Floating

Outer ring made of stainless high-performance brake steel

Inner ring anodised

Minimal wear on brake pads

With Flame design for added braking performance

Up to 20% weight saving compared to stock components;

Incl. the required CNC machined, black anodized brake caliper support for Brembo brake systems

Floating

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

With Flame design for added braking performance

With exchangeable chain track surface, therefore extremely durable

Developed for use on the toughest off-road terrain

Developed according to the requirements of our factory drivers

Visual highlight

Race look

Streamlined profile with increased coverage of swing arm mounting tabs

Large chamfered outside leading and bottom edges for maximum rock deflection

Friction reducing additives and UV protection to eliminate colour fade

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing rings

The weight-optimised water pump cover ensures maximum water flow

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

CNC milled from high-strength aluminium

Additionally hard anodised against corrosion

Protects the exhaust flange from damage and breakage

Highest quality workmanship

With exchangeable chain track surface, therefore extremely durable

Specially designed for the challenges of off-road use

Weight saving compared to series components

High stiffness and strength

Plug & Play mounting

Attachment to handlebar

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Including steering stem with steering head bearing already pressed on

CNC milled from high-strength aluminium

Additionally hard anodised against corrosion

Protects the exhaust flange from damage and breakage

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Resistant to the toughest stresses and strains

Ideal protection for sealing the fork

Mounted directly on the fork

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing rings

The weight-optimised water pump cover ensures maximum water flow

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

No fading

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Significantly longer lasting

With Flame design for added braking performance

High-quality, adjustable torque wrench 5-25 NM, including the following accessories

Push-on spoke wrenches in sizes 5.65 and 6.95mm

Push-on ratchet ¼"

Ratchet attachments: 6, 8, 10mm socket wrench, 15 Torx

Made of robust material

Pre-cut stickers

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type US

13cm tall, 3 pieces each

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall

)Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

Perfect fit

Made of high-quality carbon

Optimal protection against stone impact

Only for Brembo systems

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

For all 48mm forks

Made of high-quality carbon

Teeth made of high-strength steel, for an extra long service life

Aluminium centre section, reduces unsprung masses

Permanently joined together with high-strength rivets

At least three times longer service life than other aluminium rear sprockets

50% lighter than steel rear sprockets

Longer service life of the entire drivetrain kit

Sprockets with different teeth number as stock are CCCUO_EU!

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 999

Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm