Technical Accessories

Plug-in stand and fork support in one part

Two tools in one

Saves space when transporting your motorcycle

Stabilises the motorcycle during transport

Protects the fork shaft sealing rings and fork springs against damage due to tension belts being tightened too much

After transport, the tool serves as a perfect plug-in stand!

Elegant cover

Seat cover with transversely stitched ribs

Maximum grip with unrestricted freedom of movement

For standard height seats

Provides maximum protection at the lowest possible weight

Optimal protection against stone impact

Easy to mount

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Visual highlight

Specially developed for use in motocross

Silencer housing made of high-grade aluminium

Rich sound

Low noise level

Easy to mount

Perfect fit

Reduced weight

Recommended in combination with a FMF fatty pipe for a perfectly matched full system with optimum performance

Made of high-strength aluminium

Tested in complex and specially-developed test cycles

Position markings for easy adjustment

Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

There's racing experience here as well!

Practical tyre lever set, consisting of 3 x short version 51012092100 and 3 x long version 51012093100

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Flaps removed on ground contact

Prevents broken levers

Suitable for all hydraulic Brembo® clutch fittings

Makes removal of the front wheel easier

For all front axles with a diameter of 22mm

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Flaps removed on ground contact

Prevents broken levers

Suitable for all hydraulic Brembo® brake systems

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Protects from damage in the event of a fall

Easy to mount

Protects the swing arm

Protects from damage in the event of a fall

Easy to mount

Protects the fork

FRONT FENDER

Custom designed seat for an uncompromising look

Same seat height like the standard seat

Resistant coating

Seat cover with transversely stitched ribs

Maximum grip with unrestricted freedom of movement

Protects the intake system against water and dirt when cleaning the air filter box

AIR FILTER BOX FRONT PART

LOWER SECTION OF THE AIR FILTER

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The various cams can change the throttle valve opening speed

For all 48 mm forks

Ideal protection for sealing the fork

For use with an open fork protector

FORK PROTECTOR KIT

Extremely sturdy aluminium brackets

Prevents broken levers

Including all required assembly materials

Maximum protection against falls, flying stones, branches, etc

Indispensable companion for heavy off-road and Supermoto use

Wide, generous design in combination with sturdy aluminium bracket

Prevents broken levers

Made of robust plastic

Protects your valuable smartphone from rain, dust or mud

Touchscreen remains fully functional

Handlebar pad and smartphone holder in one

Smartphone cover with velcro fastener attached to the handlebar pad

Smartphone can be easily removed with its cover

Optimal solution for quick and secure fastening of your smartphone on the vehicle

For Smartphones up to 160 x 80mm

Comes with two separate protective strips in case the sleeve is not used

Can also be fitted in combination with the PHDS-handlebar support

Smartphone not included!

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Protects the fork shoes from damage

Easy to mount

Pre-cut stickers

Suitable for front and rear wheel rim

For wheel size 18/21"; 19/21"

Made of high strength, orange anodized aluminium; not suitable for tire mounting with mousse

With integrated ring wrench SW 32, 27, 17, 13 and 10mm