Technical Accessories

The optimum solution for always having the most important tools to hand when on the road

Secure stand for your bike

Made especially for 50 / 65 / 85 models

Aluminium construction with a non-slip pad

The top is wedge shaped and solid so the bike doesn't slide around when washing

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

Never again cold fingers!

Mounting over handlebar and switches

Better control during winter ride-outs

Anodised valve caps

With valve opener function

Practical help when loading the bike or jacking up with the rear wheel lifting device

There's racing experience here as well!

Practical tyre lever set, consisting of 3 x short version 51012092100 and 3 x long version 51012093100

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

CNC milled handlebar mount with damping rubber inserts

Gentle on wrists and shoulder joints

Damping of hard shocks

Absorption of chassis and engine vibrations

Additional handlebar damping in horizontal direction

Optimum steering precision

Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

Handlebar height adjustable to 2 positions

Anodised valve caps

Contents are in accordance with DIN standard 13167-2014 for motorcyclists

Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain

Easy to use!

Measuring range 0 bar – 4 bar

Clamping head rotatable through 90° on a flexible stainless steel feed line

The valve shaft is therefore accessed easily and quickly

Very accurate measurements by way of a durable internal membrane

Internal pressure is reduced after use by a relief valve (push button)

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

FITS: SX-E 5 2021, SX-E 5 2022, SX-E 5 2023, SX-E 3 2023, SX-E 3 2024, SX-E 5 2024

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Tool for lifting the motorcycle

Secure stand for your bike

Tool for lifting the motorcycle

Stroke: 260/370mm

Maximum load: 150kg

Comfortable unhooking of springs

Convenient and easy to use

Easy handling and operation

Visual highlight

Race look

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Stabilises the motorcycle during transport

After transport, the tool serves as a perfect plug-in stand!

13cm tall, 3 pieces each

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Pack of 100

20cm length

Prevents dirty grips

Perfect for all on the move

Exceptionally robust

Note

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280kg

With handlebar loops

With rubberised hooks and carabiner on belt ends

Recommended for storing your timecard during races

Stick it directly to the seat with grip glue

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

Magnetic

Never lose a bolt again!

Perfect for use in combination with the SX stand

These CNC-machined, high-strength aluminium handlebar risers are extremely robust thanks to their special screw fastening (from below) on the triple clamp

Twisting and bending are therefore practically impossible

Use of these handlebar risers is only possible on CNC-machined triple clamps

Available in three different heights

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280 kg

With handlebar loops

Perfect for extending lashing straps with hooks or carabiners

 Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280kg

With handlebar loops

With rubberized hooks on belt ends

Comfortable and easy to use

Fits all standard valves

Pressure display in bar or psi

Integrated pressure release valve for accurate pressure adjustment

Disengageable display and work area lighting

Energy-saving function with automatic cut-off

Maximum measuring pressure: 11 bar

Small and light, so very portable - saves the day in the event of a puncture on the move!

Mini-foot pump with pressure gauge on the swivelling valve head that fits all prevalent valves

Integrated double-cylinder with pressure switch-over to high pressure

Maximum 12 bar

Height: approximately 170mm folded together