Technical Accessories

The optimum solution for always having the most important tools to hand when on the road

Never again cold fingers!

Mounting over handlebar and switches

Better control during winter ride-outs

Anodised valve caps

With valve opener function

Secure stand for your bike

Made especially for 50 / 65 / 85 models

Aluminium construction with a non-slip pad

The top is wedge shaped and solid so the bike doesn't slide around when washing

Practical help when loading the bike or jacking up with the rear wheel lifting device

Contents are in accordance with DIN standard 13167-2014 for motorcyclists

Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain

There's racing experience here as well!

Practical tyre lever set, consisting of 3 x short version 51012092100 and 3 x long version 51012093100

Repair kit for tube tyres

Contents:

2 x Tube patches size

1 x Tube patch size 7

1 x Tube of SVS vulvanizing fluid 3g

1 x Emery paper

1 x Car valve core, short

1 x Slotted valve cap

3 x Cartridge 16g each, with freeze protector label

1 x Cartridge adapter

1 x Manual

1 x Textile storage bag

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

This mat is already mandatory for many races

Complies with FIM regulations

The special material mix absorbs overflowing fuel

The mat also facilitates the retrieval of tools, screws and other small parts during service work

Rubberised back

The special KTM design will cause a sensation in your service zone

Size: 170cm x 100cm

Tool for lifting the motorcycle

Secure stand for your bike

Tool for lifting the motorcycle

Stroke: 260/370mm

Maximum load: 150kg

Made of high strength, orange anodized aluminium; not suitable for tire mounting with mousse

With integrated ring wrench SW 32, 27, 17, 13 and 10mm

Anodised valve caps

13cm tall, 3 pieces each

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Pack of 100

20cm length

Prevents dirty grips

Perfect for all on the move

Exceptionally robust

Note

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

Made of robust material

Pre-cut stickers

Contains: 5 sheets

Adjusting the air pressure

Convenient and easy to use

Very easy operation

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280kg

With handlebar loops

With rubberised hooks and carabiner on belt ends

Keeps water out of the silencer during cleaning

For inner-diameter of 15 - 37mm

Magnetic

Never lose a bolt again!

Perfect for use in combination with the SX stand

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280 kg

With handlebar loops

Perfect for extending lashing straps with hooks or carabiners

 Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280kg

With handlebar loops

With rubberized hooks on belt ends

Comfortable and easy to use

Fits all standard valves

Pressure display in bar or psi

Integrated pressure release valve for accurate pressure adjustment

Disengageable display and work area lighting

Energy-saving function with automatic cut-off

Maximum measuring pressure: 11 bar

Small and light, so very portable - saves the day in the event of a puncture on the move!

Mini-foot pump with pressure gauge on the swivelling valve head that fits all prevalent valves

Integrated double-cylinder with pressure switch-over to high pressure

Maximum 12 bar

Height: approximately 170mm folded together

Made from high-tensile, durable steel

Highest quality workmanship

Double locking mechanism

Locking cylinder with optimum protection against any attempts at manipulation

Two keys supplied as standard

Includes rotating PVC cover that protects the cylinder lock from dirt

The ideal tool for checking perfect wheel position when tensioning the chain

Easy to use!

Measuring range 0 bar – 4 bar

Clamping head rotatable through 90° on a flexible stainless steel feed line

The valve shaft is therefore accessed easily and quickly

Very accurate measurements by way of a durable internal membrane

Internal pressure is reduced after use by a relief valve (push button)

200 m Wire with 0.61 mm diameter

Provides optimum protection

For rear sprockets up to 50T and 220mm - 260mm brake discs