Technical Accessories

Keeps water out of the silencer during cleaning

For inner-diameter of 22 - 42mm

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

Made of high-strength aluminium

Tested in complex and specially-developed test cycles

Position markings for easy adjustment

Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

There's racing experience here as well!

Practical tyre lever set, consisting of 3 x short version 51012092100 and 3 x long version 51012093100

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

CNC milled handlebar mount with damping rubber inserts

Gentle on wrists and shoulder joints

Damping of hard shocks

Absorption of chassis and engine vibrations

Additional handlebar damping in horizontal direction

Optimum steering precision

Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

Handlebar height adjustable to 2 positions

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

Closed design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Available in two different heights

Improved optics

Low version

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Including plastic insert

Reduces the risk of a lever being broken

Suitable for all Brembo® and Formula brake and clutch assembles

Comfortable unhooking of springs

Convenient and easy to use

Easy handling and operation

13cm tall, 3 pieces each

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall

)Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

Dead straight and impact-free chain track

Free from vibration – therefore the highest power transmission efficiency

Reduces the rotating masses

Angular depressions between the teeth prevent small stones and dirt particles from getting stuck under the chain

Elegant anodised surface

Extremely light

Made of high-strength aluminium

Visual highlight

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

High stiffness and strength

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Fork protector kit

Exceptionally robust

Extremely light

Headlight shroud

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 999

Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Pack of 100

20cm length

• CNC milled from high-strength aluminum
• Elegant anodised surface
• Easy to mount
• Visual highlight
• Suitable for the left and right side

Specially developed for LiFePo4-batteries

Voltages 13.2 V

Charging current - 2.5 amps

Optimizes battery performance and service life

Recovery mode for low battery voltage

Precise battery monitoring

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

The current rpm from 0-19,999 can also be displayed

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

Gain in stability at the front wheel

Fully adjustable

Top performance/price ratio

Well thought-out mounting of the damper enables individual handlebar adjustment

00050000929 handle bar support kit required for use on MY16 and on XC from MY16

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Maximum protection against falls, flying stones, branches, etc

Indispensable companion for heavy off-road and Supermoto use

Wide, generous design in combination with sturdy aluminium bracket

Prevents broken levers

Made of robust plastic

Excellent weather protection

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

Optimal protection against stone impact

Made of robust plastic

Protects against the cover being pressed in by the brake lever in the event of a fall

For the original outer clutch cover

Keeps water out of the silencer during cleaning

For inner-diameter of 15 - 37mm

Makes it easier to stand your motorcycle up

Specially developed for extreme conditions

Strap made from high-strength nylon