Technical Accessories

Never again cold fingers!

Mounting over handlebar and switches

Better control during winter ride-outs

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Including plastic insert

Reduces the risk of a lever being broken

Suitable for all Brembo® and Formula brake and clutch assembles

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

CNC milled handlebar mount with damping rubber inserts

Gentle on wrists and shoulder joints

Damping of hard shocks

Absorption of chassis and engine vibrations

Additional handlebar damping in horizontal direction

Optimum steering precision

Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

Handlebar height adjustable to 2 positions

Significantly longer lasting

Very high friction coefficient for maximum and permanent braking force

Very good braking effect even in wet conditions

For extreme operating conditions (sand, gravel...)

Eliminates “fading” almost completely

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting

Softer due to high content of organic substances

Thermal insulation by means of ceramic underlayer

Less aggressive brake feel

Lower friction coefficient than sintered brake pads

Special material mixture

Minimal wear on brake pads

Significantly longer lasting

Full version for muddy track conditions

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Includes drilling for safety wire

CNC milled from high-strength aluminium

Resistant to the toughest stresses and strains

Weight-optimised

105 Factory kit with more displacement (105 instead of 85)

Significantly more torque

Significantly more performance

100% alignment of the fork tubes

CNC milled aluminium triple clamp

Elegant anodised surface

Highly precise and smooth fork response

Including steering stem with steering head bearing already pressed on

Overall, more homogeneous force flows in the entire vehicle

No ovalization of the fork outer tube

Maximum handling gain

Optimally tuned steering stem stiffness

Visual highlight

Ideal flexibility – precisely customised to the WP fork

Specially optimised geometry of the fork clamping

Gain in stability at the front wheel

Extra strong sheet steel

Nickel-plated surface

Wide, even engine speed range

Better gas control

Combination with FMF silencer recommended

Silencer housing made of high-grade aluminium

Stainless steel silencer cap

Rich sound

Permanently welded brackets

Easy to mount

Reduced weight

For a system with optimized performance and perfect balance we recommend the combination with the FMF Fatty expansion chamber

FMF FACTORY FATTY EXPANSION CHAMBER

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Dead straight and impact-free chain track

Free from vibration – therefore the highest power transmission efficiency

Reduces the rotating masses

Elegant anodised surface

Extremely light

Made of high-strength aluminium

Visual highlight

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 999

Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

The current rpm from 0-19,999 can also be displayed

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

Recommended for extremely dusty conditions

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

A motorcycle hand grip can be mounted on the handle (not included)

The different guide plates allow a variation of the throttle valve opening

These CNC-machined, high-strength aluminium handlebar risers are extremely robust thanks to their special screw fastening (from below) on the triple clamp

Twisting and bending are therefore practically impossible

Use of these handlebar risers is only possible on CNC-machined triple clamps

Available in three different heights