Technical Accessories

The optimum solution for always having the most important tools to hand when on the road

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

Keeps water out of the silencer during cleaning

For inner-diameter of 22 - 42mm

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Never again cold fingers!

Mounting over handlebar and switches

Better control during winter ride-outs

Anodised valve caps

With valve opener function

Practical help when loading the bike or jacking up with the rear wheel lifting device

Contents are in accordance with DIN standard 13167-2014 for motorcyclists

Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain

Repair kit for tube tyres

Contents:

2 x Tube patches size

1 x Tube patch size 7

1 x Tube of SVS vulvanizing fluid 3g

1 x Emery paper

1 x Car valve core, short

1 x Slotted valve cap

3 x Cartridge 16g each, with freeze protector label

1 x Cartridge adapter

1 x Manual

1 x Textile storage bag

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

This mat is already mandatory for many races

Complies with FIM regulations

The special material mix absorbs overflowing fuel

The mat also facilitates the retrieval of tools, screws and other small parts during service work

Rubberised back

The special KTM design will cause a sensation in your service zone

Size: 170cm x 100cm

Tool for lifting the motorcycle

Secure stand for your bike

Tool for lifting the motorcycle

Stroke: 260/370mm

Maximum load: 150kg

Made of high strength, orange anodized aluminium; not suitable for tire mounting with mousse

With integrated ring wrench SW 32, 27, 17, 13 and 10mm

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Anodised valve caps

Stabilises the motorcycle during transport

After transport, the tool serves as a perfect plug-in stand!

Convenient and easy to use

Adjusting the air pressure

Made of the highest quality materials

Elegant anodised surface

Helpful tool for easier adjustment of the fork air pressure on the air fork in combination with the use of the for air pump

The quick-lock coupling remains on the air fork

13cm tall, 3 pieces each

There's racing experience here as well!

Practical tyre lever set, consisting of 3 x short version 51012092100 and 3 x long version 51012093100

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Protects the intake system against water and dirt when cleaning the air filter box

Teeth made of high-strength steel, for an extra long service life

Aluminium centre section, reduces unsprung masses

Permanently joined together with high-strength rivets

At least three times longer service life than other aluminium rear sprockets

50% lighter than steel rear sprockets

Longer service life of the entire drivetrain kit

50 teeth

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Pack of 100

20cm length

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Tested in complex and specially-developed test cycles

Made of high-strength aluminium

Position markings for easy adjustment

Comes with handlebar pad

Secure stand for your bike

Made especially for 50 / 65 / 85 models

Aluminium construction with a non-slip pad

The top is wedge shaped and solid so the bike doesn't slide around when washing

Uncompromising race look

CNC milled from high-strength aluminium

Resistant to the toughest stresses and strains

CNC milled from high-strength aluminium

Easy to mount

Optimal protection against stone impact

Prevents damage to the engine housing in the event of chain cracks

No stones drawn in between chain and engine housing (gentle on the material)

Prevents dirty grips

Perfect for all on the move

Exceptionally robust

Note

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

The current rpm from 0-19,999 can also be displayed

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible