Technical Accessories

The optimum solution for always having the most important tools to hand when on the road

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

Never again cold fingers!

Mounting over handlebar and switches

Better control during winter ride-outs

Anodised valve caps

With valve opener function

Practical help when loading the bike or jacking up with the rear wheel lifting device

Contents are in accordance with DIN standard 13167-2014 for motorcyclists

Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain

Repair kit for tube tyres

Contents:

2 x Tube patches size

1 x Tube patch size 7

1 x Tube of SVS vulvanizing fluid 3g

1 x Emery paper

1 x Car valve core, short

1 x Slotted valve cap

3 x Cartridge 16g each, with freeze protector label

1 x Cartridge adapter

1 x Manual

1 x Textile storage bag

CNC milled handlebar mount with damping rubber inserts

Gentle on wrists and shoulder joints

Damping of hard shocks

Absorption of chassis and engine vibrations

Additional handlebar damping in horizontal direction

Optimum steering precision

Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

Handlebar height adjustable to 2 positions

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

This mat is already mandatory for many races

Complies with FIM regulations

The special material mix absorbs overflowing fuel

The mat also facilitates the retrieval of tools, screws and other small parts during service work

Rubberised back

The special KTM design will cause a sensation in your service zone

Size: 170cm x 100cm

Tool for lifting the motorcycle

Secure stand for your bike

Tool for lifting the motorcycle

Stroke: 260/370mm

Maximum load: 150kg

Made of high strength, orange anodized aluminium; not suitable for tire mounting with mousse

With integrated ring wrench SW 32, 27, 17, 13 and 10mm

Anodised valve caps

13cm tall, 3 pieces each

There's racing experience here as well!

Practical tyre lever set, consisting of 3 x short version 51012092100 and 3 x long version 51012093100

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

Protects the intake system against water and dirt when cleaning the air filter box

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Pack of 100

20cm length

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Prevents dirty grips

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Perfect for all on the move

Exceptionally robust

Note

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

The current rpm from 0-19,999 can also be displayed

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

Made of robust material

Pre-cut stickers

Contains: 5 sheets

Includes drilling for safety wire

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Adjusting the air pressure

Convenient and easy to use

Very easy operation

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280kg

With handlebar loops

With rubberised hooks and carabiner on belt ends

Recommended for storing your timecard during races

Stick it directly to the seat with grip glue

100mm length

20 blades: 0.05 - 0.1 - 0.15 - 0.2 - 0.25 - 0.3- 0.35 - 0.4 - 0.45 - 0.5 - 0.55 - 0.6 - 0.65 - 0.7 - 0.75 - 0.8 - 0.85 - 0.9 - 0.95 - 1.0mm

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special