Technical Accessories

Pre-cut stickers

Suitable for front and rear wheel rim

For wheel size 18/21"; 19/21"

4 pieces 37mm x 31mm

4 pieces 48mm x 40mm

Manufactured using state-of-the-art 2-component injection moulding technology

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tyre changes, brake service etc. without removing the brake cover

Noble material mix of carbon fibre and plastic

Manufactured using state-of-the-art 2-component injection moulding technology

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tyre changes, brake service etc. without removing the brake cover

Additional protection against water splashes and sludge

For extremely muddy conditions

Developed according to the requirements of our factory drivers

Reduced weight

Self adhesive special foam, prevents mud and dirt from sticking to your plastics and in this way prevents your bike from gaining weight during riding in muddy conditions

Spoiler set

SPOILER SET

FRONT NUMBER PLATE

Resistant coating

Highly elastic foam for extra comfort

Same seat height like the standard seat

Developed according to the requirements of our factory drivers

Resistant coating

Special gradation for good grip even when accelerating hard

Standard seat height

Same seat height like the standard seat

Elegant cover

Resistant coating

Plenty of freedom of movement and yet perfect hold

The “Wave surface” has the effect of a gradation

Same seat height like the standard seat

Resistant coating

Higher compared to the standard seat

Specially designed for riders with a height of above 1.90m

Resistant coating

Higher compared to the standard seat

Specially designed for riders with a height of above 1.80m

Ergonomically perfect shape (the result of years of racing experience)

Longer reach due to bigger volume (SX-F models)

IMS Dry-break system can be mounted

For use without IMS System, the flange 79707913055 is included in the kit to use the stock filler cap (Enduro)

For use on SX-F / SMR models, fuel pump 79707088300 is required

For use on SX-F / SMR models, an Enduro filler cap is required (78107908144 or Enduro stock filler cap)

Optimised air flow

Left hand

Optimised air flow

Left hand side fairing

Right hand air filter panel

Left hand air filter cover

Air filter box front part

Lower section of air filter

WRAP-AROUND HANDGUARD KIT

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

Attachment to handlebar

Plug & Play mounting

Characteristic of the throttle response can be varied

Activate traction control for the two different engine configurations

To ensure the sensor magnet is in the correct location even after a change from Enduro to Supermoto wheels

Sensor magnet 58214050054 is required

Increases the volume of the rear master cylinder

Additional cooling ribs minimise the heating of the brake fluid

Eliminates “fading” almost completely

Total height including cover approximately 26.5mm

Keeps water out of the silencer during cleaning

For inner-diameter of 15 - 37mm

To prevent the ingress of water in the silencer when cleaning

For inner diameters 15 mm - 38 mm

Keeps water out of the silencer during cleaning

For internal diameters 37 mm - 62 mm

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Visual highlight

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Makes removal of the front wheel easier

For all front axles with a diameter of 22mm