Technical Accessories

Colour differences between the upper and lower triple clamp cannot be technically ruled out

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Optimally tuned steering stem stiffness

100% alignment of the fork tubes

Ideal flexibility – precisely customised to the WP fork

Including steering stem with steering head bearing already pressed on

Required items for installation on SX models from model year 2016:

Handlebar mount kit 78901939044/144/244/344/444 or

PHDS SXS07125200

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

Original fairing parts, without the standard decor

Optimal basis for creating a unique design

Perfect fit

Personalise the look of your motorcycle

Kit contains:

Fender

Air filter cover

Air filter panel

Side fairing

Start number plate

Spoiler set

Headlight shroud

Tail section

Fork protector

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 999

Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Pack of 100

20cm length

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Secure stand for your bike

Aluminium construction with non-slip underlay so the motorcycle does not slip during washing

Clear pressure point across the entire temperature range

More brake power

Higher stiffness with the same weight

Made of high-strength aluminium

Clear pressure point across the entire temperature range

More brake power

Higher stiffness with the same weight

Made of high-strength aluminium

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Prevents dirty grips

Optimal solution for quick and secure fastening of your smartphone on the vehicle

Protects your valuable smartphone from rain, dust or mud

Touchscreen remains fully functional

New "SPC+" mounting system, but there is also an adapter included to mount the case also on the previous mounting system

Size 153 x 70 mm

Optimal solution for quick and secure fastening of your smartphone on the vehicle

Protects your valuable smartphone from rain, dust or mud

Touchscreen remains fully functional

New "SPC+" mounting system, but there is also an adapter included to mount the case also on the previous mounting system

Optimal solution for quick and secure fastening of your smartphone on the vehicle

Get´s mounted with a 3M adhesive pad directly on the back side of a smartphone, or any smartphone case

New "SPC+" mounting system, but there is also an adapter included to mount this universal adapter also on the previous mounting system

Dimensions: 66 x 55mm (2.6 x 2.17 inch)

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

This clever tool is a must for every motorcycle toolbox

With it, you can remove dirt from your fork seals effortlessly

No matter whether it's in the garage or directly at the racetrack this tool extends the life of your seals many times over

For all 48mm forks

Specially developed for LiFePo4-batteries

Voltages 13.2 V

Charging current - 2.5 amps

Optimizes battery performance and service life

Recovery mode for low battery voltage

Precise battery monitoring

Perfect for all on the move

Exceptionally robust

Note

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

The current rpm from 0-19,999 can also be displayed

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

Gain in stability at the front wheel

Fully adjustable

Top performance/price ratio

Well thought-out mounting of the damper enables individual handlebar adjustment

00050000929 handle bar support kit required for use on MY16 and on XC from MY16

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Fast preload adjustment

Use of the entire length of the thread on the shock absorber

Very easy operation

Extremely low weight

Dirt-resistance

Mechanical drive

Provides more traction when starting

Made of high-strength aluminium

Elegant anodised surface

Pure race feeling

Mounted directly on the OEM-fork

Highest quality workmanship

The right combination of look, style, and performance

Specially designed for the challenges of off-road use

Made from special, high-strength plastic for maximum stability

With exchangeable chain track surface, therefore extremely durable

Specially designed for the challenges of off-road use

Significantly longer durability

Made of high-strength aluminium

The right combination of look, style, and performance

The lightest Renthal Sprocket on the market

Provide maximum power transfer and long-life due to advanced tooth profile and perfect concentricity

Combination of a high strength base material and exceptionally hardwearing surface

Specially designed for the challenges of off-road use

Significantly longer durability

Made of high-strength aluminium

The right combination of look, style, and performance

The lightest Renthal Sprocket on the market

Provide maximum power transfer and long-life due to advanced tooth profile and perfect concentricity

Combination of a high strength base material and exceptionally hardwearing surface

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Perfect fit

Made of high-quality carbon

Optimal protection against stone impact

Only for Brembo systems

Perfect fit

Made of high-quality carbon

Optimal protection against stone impact

Only for Brembo systems

For all 48 mm forks

Ideal protection for sealing the fork

For use with an open fork protector