Technical Accessories

Resistant coating

Higher compared to the standard seat

Specially designed for riders with a height of above 1.80m

Ergonomically perfect shape (the result of years of racing experience)

Longer reach due to bigger volume (SX-F models)

IMS Dry-break system can be mounted

For use without IMS System, the flange 79707913055 is included in the kit to use the stock filler cap (Enduro)

For use on SX-F / SMR models, fuel pump 79707088300 is required

For use on SX-F / SMR models, an Enduro filler cap is required (78107908144 or Enduro stock filler cap)

Optimised air flow

Left hand

Optimised air flow

Left hand side fairing

Right hand air filter panel

Left hand air filter cover

Air filter box front part

Lower section of air filter

Easy to mount

Protects the linkage from damage

WRAP-AROUND HANDGUARD KIT

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Optimally tuned steering stem stiffness

100% alignment of the fork tubesIdeal flexibility – precisely customised to the WP fork

Specially optimised geometry of the fork clamping

No ovalization of the fork outer tube

Highly precise and smooth fork response

Maximum handling gain

Gain in stability at the front wheel

Overall, more homogeneous force flows in the entire vehicle

Simple offset adjustment

Including steering stem with steering head bearing already pressed on

Very simple offset adjustment of 20 or 22mm

Shorter offset: Stability on fast straights

Longer offset: easier and quicker cornering in curves

Colour differences between the upper and lower triple clamp cannot be technically ruled out

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

Increases the volume of the rear master cylinder

Additional cooling ribs minimise the heating of the brake fluid

Eliminates “fading” almost completely

Total height including cover approximately 26.5mm

STEERING DAMPER COUNTER BEARING

STEERING DAMPER BRACKET

Keeps water out of the silencer during cleaning

For inner-diameter of 15 - 37mm

To prevent the ingress of water in the silencer when cleaning

For inner diameters 15 mm - 38 mm

Keeps water out of the silencer during cleaning

For internal diameters 37 mm - 62 mm

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Visual highlight

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Particularly safe due to clever design

Clutch is secured by simply twisting the connection

Recommended for extremely dusty conditions

Recommended in extremely wet conditions

Acts as an additional protective layer

Recommended for extremely dusty conditions

Premature sanding of the air filter is avoided

Coarse-pored air filter cover

Protects the footpegs from damage during a potential fall

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Already mandatory in many competitions

Provides optimum protection

Visual highlight

With the integrated card holder you always have the time in view

A small extra pocket allows you to stow small items

Can also be fitted in combination with the PHDS-handlebar support

A motorcycle hand grip can be mounted on the handle (not included)

The different guide plates allow a variation of the throttle valve opening

For use with an open fork protector

Conversion of the standard damped handlebar mount into a rigid one