Technical Accessories

Stainless steel outer sleeve and interior

Can only be fitted with a standard header

Full sound

Uncompromising race look

Hard Enduro-compatible durability

Complies with current FIM noise regulations

Better power delivery

Sensitive response

Silencer housing made of high-grade aluminium

Carbon silencer cap

Mounting also possible with original header

Significantly more torque

Substantial weight saving

Noticeable performance enhancement

In connection with an FMF Megabomb header even further increase in rideability and power output can be achieved

This mat is already mandatory for many races

The special material mix absorbs overflowing fuel

The mat also facilitates the retrieval of tools, screws and other small parts during service work

Complies with FIM regulations

Rubberised back

Size: 200cm x 100cm

On this spoke wrench, the torque is preset at 6 Nm

This prevents over-tightening of the spoke nipples

Too much torque when tightening the spoke nipples is the most frequent cause of broken spokes

Wrench size 6.8mm

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Higher opening pressure compared to standard

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Visual highlight

Floating

Outer ring made of stainless high-performance brake steel

Inner ring anodised

Minimal wear on brake pads

With Flame design for added braking performance

Up to 20% weight saving compared to stock components;

Incl. the required CNC machined, black anodized brake caliper support for Brembo brake systems

Floating

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

With Flame design for added braking performance

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing rings

Manifold routing optimally adapted to the production engine

Silencer housing made of high-grade titanium

Complies with current FIM noise regulations

Complies with current AMA noise regulations

Stainless steel header

More usable speed range

Better power delivery

Improved handling overall due to finer dosing capacity on the throttle grip

Sensitive response

Rich sound

Increased tightening torque

Increased performance

Made from high grade titanium

Uncompromising race look

Permanently welded brackets

Complies with current FIM noise regulations

Substantial weight saving

Visual highlight

Changes the handling of the motorcycle

Gain in stability therefore recommended for fast tracks

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Including steering stem with steering head bearing already pressed on

Made of the highest quality materials

Tested in the toughest conditions

Developed together with the vehicle

Enables shorter drivers to also achieve the optimum seat height

Perfect compromise between maximum chassis performance and lowest possible vehicle height

No restrictions on riding dynamics

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Resistant to the toughest stresses and strains

Ideal protection for sealing the fork

Mounted directly on the fork

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing rings

No fading

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Significantly longer lasting

With Flame design for added braking performance

Universal and inconspicuous bracket for your smartphone

Optimal solution for quick and secure fastening of your smartphone on the vehicle

Can be clamped on the handlebar (including different adapter)

The arm can be rotated in any position for the perfect position for your smartphone

Includes also a anti vibration module which decouples the smartphone from the bracket / motorcycle with a specific developed elastomer inlay

It reduces the transfer of vibrations, generated by the motorcycle, to the smartphone and protects it`s sensitive components

New "SPC+" mounting system

Made of robust material

Pre-cut stickers

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing rings

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type US

13cm tall, 3 pieces each

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall

)Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Teeth made of high-strength steel, for an extra long service life

Aluminium centre section, reduces unsprung masses

Permanently joined together with high-strength rivets

At least three times longer service life than other aluminium rear sprockets

50% lighter than steel rear sprockets

Longer service life of the entire drivetrain kit

Sprockets with different teeth number as stock are CCCUO_EU!

Exceptionally robust

Extremely light

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 999

Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm