Technical Accessories

Made of robust plastic

Fastening independent of fittings directly on the handlebars

To convert the open, standard handguards to a closed version

Teeth made of high-strength steel, for an extra long service life

Aluminium centre section, reduces unsprung masses

Permanently joined together with high-strength rivets

At least three times longer service life than other aluminium rear sprockets

50% lighter than steel rear sprockets

Longer service life of the entire drivetrain kit

Sprockets with different teeth number as stock are CCCUO_EU!

Resistant to the toughest stresses and strains

Forged lightening indents reduce rotational mass

Grooves between the teeth clear dirt under the chain

Extends chain life

Protects the motorcycle from dust, scratches and the like

The indoor bike cover makes every KTM an eye-catcher in the garage

Completely dust and dirt-impermeable fabric

Material with special structure

The inside is softly padded

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Made of robust plastic

Fastening independent of fittings directly on the handlebars

To convert the open, standard handguards to a closed version

The optimum solution for always having the most important tools to hand when on the road

Keeps water out of the silencer during cleaning

For inner-diameter of 22 - 42mm

Made of robust plastic

To convert the open, standard handguards to a closed version

Usable with handguards 7960297900028/30AB and 2650297900028/30/AB

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Ergonomically perfect shape (the result of years of racing experience)

Adjustable grip width

Suitable for all hydraulic Brembo® clutch mountings

Anodised valve caps

With valve opener function

Optimal solution for quick and secure fastening of your smartphone on the vehicle

Dimensions: 66 x 55mm (2.6 x 2.17 inch)

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Prevents the hand grips from chafing in the event of a fall

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Adjustable grip width

Already mandatory in many competitions

Provides optimum protection

Visual highlight

Can also be fitted in combination with the PHDS-handlebar support

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Never again cold fingers!

Mounting over handlebar and switches

Better control during winter ride-outs

Resistant coating

Enables shorter drivers to also achieve the optimum seat height

Lower compared to the standard seat

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Warm hands, no matter what the weather

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

Visual highlight

Perfect fit

Practical help when loading the bike or jacking up with the rear wheel lifting device

Contents are in accordance with DIN standard 13167-2014 for motorcyclists

Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain

Made of high-strength aluminium

Tested in complex and specially-developed test cycles

Position markings for easy adjustment

Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

There's racing experience here as well!

Practical tyre lever set, consisting of 3 x short version 51012092100 and 3 x long version 51012093100

Repair kit for tube tyres

Contents:

2 x Tube patches size

1 x Tube patch size 7

1 x Tube of SVS vulvanizing fluid 3g

1 x Emery paper

1 x Car valve core, short

1 x Slotted valve cap

3 x Cartridge 16g each, with freeze protector label

1 x Cartridge adapter

1 x Manual

1 x Textile storage bag

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Flaps removed on ground contact

Prevents broken levers

Suitable for all hydraulic Brembo® clutch fittings

Makes removal of the front wheel easier

For all front axles with a diameter of 22mm

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Flaps removed on ground contact

Prevents broken levers

Suitable for all hydraulic Brembo® brake systems

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

CNC milled handlebar mount with damping rubber inserts

Gentle on wrists and shoulder joints

Damping of hard shocks

Absorption of chassis and engine vibrations

Additional handlebar damping in horizontal direction

Optimum steering precision

Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

Handlebar height adjustable to 2 positions

Includes an anti vibration module which decouples the smartphone from the bracket/motorcycle with a specific developed elastomer inlay

It reduces the transfer of vibrations, generated by the motorcycle, to the smartphone and protects it`s sensitive components

Can be mounted on older versions of the smartphone bracket to adapt it to the new "SPC+" mounting system