Technical Accessories

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing rings

Made of robust material

Pre-cut stickers

Contains: 5 sheets

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Protects the fork shoes from damage

Easy to mount

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

6mm wider contact surface than standard

Improves clutch performance and durability

Hinson-typical surface treatment for significantly improved robustness compared to the standard part

Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled

Can be installed in the standard clutch or in combination with other Hinson clutch components

CNC milled from high-strength aluminium

Improves heat dissipation

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Wider contact surface than standard:

+8mm at 125/150 SX/XC-W, SX-F, 450/500 EXC-F

+16mm at 250/300 SX/EXC, 250/350 EXC-F

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280kg

With handlebar loops

With rubberised hooks and carabiner on belt ends

Recommended for storing your timecard during races

Stick it directly to the seat with grip glue

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

100mm length

20 blades: 0.05 - 0.1 - 0.15 - 0.2 - 0.25 - 0.3- 0.35 - 0.4 - 0.45 - 0.5 - 0.55 - 0.6 - 0.65 - 0.7 - 0.75 - 0.8 - 0.85 - 0.9 - 0.95 - 1.0mm

Pre-cut stickers

Suitable for front and rear wheel rim

For wheel size 18/21"; 19/21"

4 pieces 37mm x 31mm

4 pieces 48mm x 40mm

Manufactured using state-of-the-art 2-component injection moulding technology

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tyre changes, brake service etc. without removing the brake cover

Noble material mix of carbon fibre and plastic

Manufactured using state-of-the-art 2-component injection moulding technology

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tyre changes, brake service etc. without removing the brake cover

WRAP-AROUND HANDGUARD KIT

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

To ensure the sensor magnet is in the correct location even after a change from Enduro to Supermoto wheels

Sensor magnet 58214050054 is required

Increases the volume of the rear master cylinder

Additional cooling ribs minimise the heating of the brake fluid

Eliminates “fading” almost completely

Total height including cover approximately 26.5mm

To prevent the ingress of water in the silencer when cleaning

For inner diameters 15 mm - 38 mm

Keeps water out of the silencer during cleaning

For internal diameters 37 mm - 62 mm

Makes removal of the front wheel easier

For all front axles with a diameter of 22mm

Already mandatory in many competitions

Provides optimum protection

Visual highlight

With the integrated card holder you always have the time in view

A small extra pocket allows you to stow small items

Can also be fitted in combination with the PHDS-handlebar support

Made of high-strength aluminium

Improved braking performance

Required for using a 270 mm brake disc and 2-piston Brembo brake caliper

Floating

Inner ring anodised

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

With Flame design for added braking performance

Makes it easier to stand your motorcycle up

Specially developed for extreme conditions

Strap made from high-strength nylon

Tool for lifting the motorcycle

Secure stand for your bike

Stroke: 315/425mm

Maximum load: 150kg

Transparent plastic canister including a flexible hose and screw cap

For legal reasons, not to be used in some countries for storage and transportation of gasoline

Pre-cut stickers

Suitable for front and rear wheel rim

For wheel size 18/21"; 19/21"

Prevents dust and dirt from entering the tank when the fuel tank cap is opened

Filter is attached directly to the tank opening

Fits all 3/4 fuel tank caps