Technical Accessories

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall

)Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

There's racing experience here as well!

Practical tyre lever set, consisting of 3 x short version 51012092100 and 3 x long version 51012093100

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

For all 48mm forks

Made of high-quality carbon

Makes removal of the front wheel easier

For all front axles with a diameter of 22mm

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 999

Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Pack of 100

20cm length

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Secure stand for your bike

Aluminium construction with non-slip underlay so the motorcycle does not slip during washing

Clear pressure point across the entire temperature range

More brake power

Higher stiffness with the same weight

Made of high-strength aluminium

Clear pressure point across the entire temperature range

More brake power

Higher stiffness with the same weight

Made of high-strength aluminium

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Prevents dirty grips

Extremely robust spark plug

Centre electrode tip made of iridium

Reinforced ground electrode (against vibration and breakage)

Special design with improved anti-sooting characteristic

Recommended in combination with factory cylinder heads, factor exhaust systems or factory digital box

Fast preload adjustment

Use of the entire length of the thread on the shock absorber

Very easy operation

Extremely low weight

Dirt-resistance

Mechanical drive

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

This clever tool is a must for every motorcycle toolbox

With it, you can remove dirt from your fork seals effortlessly

No matter whether it's in the garage or directly at the racetrack this tool extends the life of your seals many times over

For all 48mm forks

Perfect for all on the move

Exceptionally robust

Note

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

The current rpm from 0-19,999 can also be displayed

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Provides more traction when starting

Made of high-strength aluminium

Elegant anodised surface

Pure race feeling

Mounted directly on the OEM-fork

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

Anodised hub milled from a whole piece

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Reinforced spokes for higher impact resistance

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Prevents dust and dirt from entering the tank when the fuel tank cap is opened

Filter is attached directly to the tank opening

HANDLEBAR MOUNT

Designed to completely change the original look of your motorcycle

Glue the graphics kit directly onto the standard fairing parts

Can be removed without leaving any residue

Made of the highest quality materials

Visual highlight

Perfect fit

Perfect fit

Visual highlight

Protects the radiator from mud, dirt and sand

Protection against rapid overheating of the engine in muddy conditions

Provides maximum protection at the lowest possible weight

Optimal protection against stone impact

Easy to mount

Provides maximum protection at the lowest possible weight

Optimal protection against stone impact

Easy to mount