Technical Accessories

Elegant cover

Resistant coating

Plenty of freedom of movement and yet perfect hold

The “Wave surface” has the effect of a gradation

Same seat height like the standard seat

Resistant coating

Higher compared to the standard seat

Specially designed for riders with a height of above 1.90m

Resistant coating

Higher compared to the standard seat

Specially designed for riders with a height of above 1.80m

Optimised air flow

Left hand

Optimised air flow

Left hand side fairing

Right hand air filter panel

Left hand air filter cover

Air filter box front part

Lower section of air filter

WRAP-AROUND HANDGUARD KIT

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

To ensure the sensor magnet is in the correct location even after a change from Enduro to Supermoto wheels

Sensor magnet 58214050054 is required

Increases the volume of the rear master cylinder

Additional cooling ribs minimise the heating of the brake fluid

Eliminates “fading” almost completely

Total height including cover approximately 26.5mm

Keeps water out of the silencer during cleaning

For inner-diameter of 15 - 37mm

To prevent the ingress of water in the silencer when cleaning

For inner diameters 15 mm - 38 mm

Keeps water out of the silencer during cleaning

For internal diameters 37 mm - 62 mm

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Visual highlight

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Makes removal of the front wheel easier

For all front axles with a diameter of 22mm

Recommended for extremely dusty conditions

Recommended in extremely wet conditions

Acts as an additional protective layer

Recommended for extremely dusty conditions

Premature sanding of the air filter is avoided

Coarse-pored air filter cover

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Already mandatory in many competitions

Provides optimum protection

Visual highlight

With the integrated card holder you always have the time in view

A small extra pocket allows you to stow small items

Can also be fitted in combination with the PHDS-handlebar support

A motorcycle hand grip can be mounted on the handle (not included)

The different guide plates allow a variation of the throttle valve opening

For use with an open fork protector

Made of high-strength aluminium

Improved braking performance

Required for using a 270 mm brake disc and 2-piston Brembo brake caliper

No fading

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Significantly longer lasting

With Flame design for added braking performance

Extra thick: 4.6mm

Floating

Inner ring anodised

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

With Flame design for added braking performance

Makes it easier to stand your motorcycle up

Specially developed for extreme conditions

Strap made from high-strength nylon