Technical Accessories

Prevents dirty grips

Extremely robust spark plug

Centre electrode tip made of iridium

Reinforced ground electrode (against vibration and breakage)

Special design with improved anti-sooting characteristic

Recommended in combination with factory cylinder heads, factor exhaust systems or factory digital box

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Perfect for all on the move

Exceptionally robust

Note

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

The current rpm from 0-19,999 can also be displayed

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Highest quality workmanship

The right combination of look, style, and performance

Specially designed for the challenges of off-road use

Made from special, high-strength plastic for maximum stability

With exchangeable chain track surface, therefore extremely durable

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

Made of robust material

Pre-cut stickers

Contains: 5 sheets

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

Includes drilling for safety wire

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Adjusting the air pressure

Convenient and easy to use

Very easy operation

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280kg

With handlebar loops

With rubberised hooks and carabiner on belt ends

Recommended for storing your timecard during races

Stick it directly to the seat with grip glue

100mm length

20 blades: 0.05 - 0.1 - 0.15 - 0.2 - 0.25 - 0.3- 0.35 - 0.4 - 0.45 - 0.5 - 0.55 - 0.6 - 0.65 - 0.7 - 0.75 - 0.8 - 0.85 - 0.9 - 0.95 - 1.0mm

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

Keeps water out of the silencer during cleaning

For inner-diameter of 15 - 37mm

To prevent the ingress of water in the silencer when cleaning

For inner diameters 15 mm - 38 mm

Keeps water out of the silencer during cleaning

For internal diameters 37 mm - 62 mm

Recommended for extremely dusty conditions

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

A motorcycle hand grip can be mounted on the handle (not included)

The different guide plates allow a variation of the throttle valve opening

No fading

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Significantly longer lasting

With Flame design for added braking performance

Extra thick: 4.6mm

Transparent plastic canister including a flexible hose and screw cap

For legal reasons, not to be used in some countries for storage and transportation of gasoline

Race look

Visual highlight

With exchangeable chain track surface, therefore extremely durable

Specially designed for the challenges of off-road use

CNC machined out of teflon

Visual highlight

Race look

Magnetic

Never lose a bolt again!

Perfect for use in combination with the SX stand

Perfect for all 2-stroke riders on the move

The small bottle fits in your tool bag or jacket

Capacity 250 ml, with scaling for different mixture ratios (1:40 / 2.5%; 1:50 / 2%; 1:60 / 1.7%; 1:80 / 1.25%)

With scaling for both the fluid level and different mixture ratios

Perfect for changing the oil and for preparing larger quantities of 2-stroke mixture in the canister

Simple handling thanks to the ergonomic design

Practical tool for setting preload on the shock absorber without having to remove it

CNC milled from high-strength aluminium

Not lockable

Extremely fast and keyless refuelling