Technical Accessories

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

To ensure the sensor magnet is in the correct location even after a change from Enduro to Supermoto wheels

Sensor magnet 58214050054 is required

Increases the volume of the rear master cylinder

Additional cooling ribs minimise the heating of the brake fluid

Eliminates “fading” almost completely

Total height including cover approximately 26.5mm

Keeps water out of the silencer during cleaning

For inner-diameter of 15 - 37mm

To prevent the ingress of water in the silencer when cleaning

For inner diameters 15 mm - 38 mm

Keeps water out of the silencer during cleaning

For internal diameters 37 mm - 62 mm

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Visual highlight

Makes removal of the front wheel easier

For all front axles with a diameter of 22mm

Already mandatory in many competitions

Provides optimum protection

Visual highlight

With the integrated card holder you always have the time in view

A small extra pocket allows you to stow small items

Can also be fitted in combination with the PHDS-handlebar support

Made of high-strength aluminium

Improved braking performance

Required for using a 270 mm brake disc and 2-piston Brembo brake caliper

No fading

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Significantly longer lasting

With Flame design for added braking performance

Extra thick: 4.6mm

Floating

Inner ring anodised

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

With Flame design for added braking performance

Makes it easier to stand your motorcycle up

Specially developed for extreme conditions

Strap made from high-strength nylon

Improves clutch performance and durability

Hinson-typical surface treatment for significantly improved robustness compared to the standard part

Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled

Can be installed in the standard clutch or in combination with other Hinson clutch components

CNC milled from high-strength aluminium

Improves heat dissipation

Tool for lifting the motorcycle

Secure stand for your bike

Stroke: 315/425mm

Maximum load: 150kg

Transparent plastic canister including a flexible hose and screw cap

For legal reasons, not to be used in some countries for storage and transportation of gasoline

Pre-cut stickers

Suitable for front and rear wheel rim

For wheel size 18/21"; 19/21"

Prevents dust and dirt from entering the tank when the fuel tank cap is opened

Filter is attached directly to the tank opening

Fits all 3/4 fuel tank caps

Magnetic

Never lose a bolt again!

Perfect for use in combination with the SX stand

Perfect for all 2-stroke riders on the move

The small bottle fits in your tool bag or jacket

Capacity 250 ml, with scaling for different mixture ratios (1:40 / 2.5%; 1:50 / 2%; 1:60 / 1.7%; 1:80 / 1.25%)

With scaling for both the fluid level and different mixture ratios

Perfect for changing the oil and for preparing larger quantities of 2-stroke mixture in the canister

Simple handling thanks to the ergonomic design

With return valve

Anodised dust protection cap

Quick and easy bleeding of the brake

Closed design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Available in two different heights

Improved optics

Low version

Closed design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Available in two different heights

Improved optics

Low version

Practical tool for setting preload on the shock absorber without having to remove it

High stiffness and strength

Made of high-quality carbon

Optimal protection against stone impact

Visual highlight

Optimal protection against stone impact

Can be installed on brake caliper supports 77713975044, 79613975044, 7771397501030, 7771397511030, 78113975044, 78113975144, 78113975244, 78913975044 or 78913975144

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

Enables power consumers such as grip heater or radiator fans to be installed on motocross or cross-country models as well

The power consumer is now connected directly to the battery

Consequently, the battery is also drained when the engine is not running, unless the consumer is switched off

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Including plastic insert

Reduces the risk of a lever being broken

Suitable for all Brembo® and Formula brake and clutch assembles

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280 kg

With handlebar loops

Perfect for extending lashing straps with hooks or carabiners

 Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280kg

With handlebar loops

With rubberized hooks on belt ends

Comfortable and easy to use

Fits all standard valves

Pressure display in bar or psi

Integrated pressure release valve for accurate pressure adjustment

Disengageable display and work area lighting

Energy-saving function with automatic cut-off

Maximum measuring pressure: 11 bar

Small and light, so very portable - saves the day in the event of a puncture on the move!

Mini-foot pump with pressure gauge on the swivelling valve head that fits all prevalent valves

Integrated double-cylinder with pressure switch-over to high pressure

Maximum 12 bar

Height: approximately 170mm folded together

6mm and 6.8mm