Technical Accessories

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing rings

Manifold routing optimally adapted to the production engine

Silencer housing made of high-grade titanium

Complies with current FIM noise regulations

Complies with current AMA noise regulations

Stainless steel header

More usable speed range

Better power delivery

Improved handling overall due to finer dosing capacity on the throttle grip

Sensitive response

Rich sound

Increased tightening torque

Increased performance

Makes it easier to stand your motorcycle up

Essential under extreme off-road conditions

Strap made from high-strength nylon

Made of the highest quality materials

Tested in the toughest conditions

Developed together with the vehicle

Enables shorter drivers to also achieve the optimum seat height

Perfect compromise between maximum chassis performance and lowest possible vehicle height

No restrictions on riding dynamics

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

Made from high grade titanium

Uncompromising race look

Permanently welded brackets

Complies with current FIM noise regulations

Substantial weight saving

Visual highlight

Changes the handling of the motorcycle

Gain in stability therefore recommended for fast tracks

Weight-optimised

Visual highlight with technical and ergonomic added value

Maximum handling gain

Changes the handling of the motorcycle

Gain in handling therefore recommended for tighter tracks

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Including steering stem with steering head bearing already pressed on

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

Made of the highest quality materials

Tested in the toughest conditions

Developed together with the vehicle

Enables shorter drivers to also achieve the optimum seat height

Perfect compromise between maximum chassis performance and lowest possible vehicle height

No restrictions on riding dynamics

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Resistant to the toughest stresses and strains

Ideal protection for sealing the fork

Mounted directly on the fork

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing rings

No fading

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Significantly longer lasting

With Flame design for added braking performance

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing rings

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type US

13cm tall, 3 pieces each

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall

)Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

There's racing experience here as well!

Practical tyre lever set, consisting of 3 x short version 51012092100 and 3 x long version 51012093100

Perfect fit

Made of high-quality carbon

Optimal protection against stone impact

Only for Brembo systems

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

For all 48mm forks

Made of high-quality carbon

Teeth made of high-strength steel, for an extra long service life

Aluminium centre section, reduces unsprung masses

Permanently joined together with high-strength rivets

At least three times longer service life than other aluminium rear sprockets

50% lighter than steel rear sprockets

Longer service life of the entire drivetrain kit

Sprockets with different teeth number as stock are CCCUO_EU!

Exceptionally robust

Extremely light

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Makes removal of the front wheel easier

For all front axles with a diameter of 22mm

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 999

Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Pack of 100

20cm length

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight