Products

With scaling for both the fluid level and different mixture ratios

Perfect for changing the oil and for preparing larger quantities of 2-stroke mixture in the canister

Simple handling thanks to the ergonomic design

Protects the intake system against water and dirt when cleaning the air filter box

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

Practical help when loading the bike or jacking up with the rear wheel lifting device

Perfect for all on the move

Exceptionally robust

Note

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Visual highlight

Race look

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Including plastic insert

Reduces the risk of a lever being broken

Suitable for all Brembo® and Formula brake and clutch assembles

CNC milled from high-strength aluminium

Easy to mount

Optimal protection against stone impact

Prevents damage to the engine housing in the event of chain cracks

No stones drawn in between chain and engine housing (gentle on the material)

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Uncompromising race look

CNC milled from high-strength aluminium

Resistant to the toughest stresses and strains

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Provides more traction when starting

Made of high-strength aluminium

Elegant anodised surface

Pure race feeling

Mounted directly on the OEM-fork

100mm length

20 blades: 0.05 - 0.1 - 0.15 - 0.2 - 0.25 - 0.3- 0.35 - 0.4 - 0.45 - 0.5 - 0.55 - 0.6 - 0.65 - 0.7 - 0.75 - 0.8 - 0.85 - 0.9 - 0.95 - 1.0mm

Contents are in accordance with DIN standard 13167-2014 for motorcyclists

Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain

 Extra strong sheet steel

Nickel-plated surface

Wide, even engine speed range

Higher speed

More traction

Better gas control

Combination with FMF silencer recommended

FITS: 65 SX 2020, 65 SX 2021, 65 SX 2022, 65 SX 2023

Specially developed for use in motocross

Silencer housing made of high-grade aluminium

Stainless steel silencer cap

Rich sound

Low noise level

Permanently welded brackets

Easy to mount

Perfect fit

Reduced weight

For a system with optimized performance and perfect balance we recommend the combination with the FMF Fatty expansion chamber

FITS: 65 SX 2020, 65 SX 2021, 65 SX 2022, 65 SX 2023

Small and light, so very portable - saves the day in the event of a puncture on the move!

Mini-foot pump with pressure gauge on the swivelling valve head that fits all prevalent valves

Integrated double-cylinder with pressure switch-over to high pressure

Maximum 12 bar

Height: approximately 170mm folded together

Adjusting the air pressure

Convenient and easy to use

Very easy operation

Protects the frame without changing the slim lines of your motorcycle

Prevents dust and dirt from entering the tank when the fuel tank cap is opened

Filter is attached directly to the tank opening

Fits all 3/4 fuel tank caps

Funnel specially developed for KTM motorcycles

Diameter (small and large) optimized to suit the filler neck; special groove for optimum ventilation

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

Prevents dirty grips

Developed according to the requirements of our factory drivers

Less stress when riding

Objective: comfort AND safety

Ergonomic contour adapted to the shape of the hand for maximum comfort

Half waffle grip

For a secure grip

Three areas for the metal wire locking

Version: soft

Developed according to the requirements of our factory drivers

Less stress when riding

Objective: comfort AND safety

Ergonomic contour adapted to the shape of the hand for maximum comfort

Half waffle grip

For a secure grip

Three areas for the metal wire locking

Version: medium

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions