Products

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Visual highlight

Perfect fit

Made of high-strength aluminium

Tested in complex and specially-developed test cycles

Position markings for easy adjustment

Dimensions: A = 115 mm, B = 806 mm, C = 62 mm

Universally applicable for mounting the GPS bracket

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Prevents the hand grips from chafing in the event of a fall

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

Never again cold fingers!

Mounting over handlebar and switches

Better control during winter ride-outs

Already mandatory in many competitions

Provides optimum protection

Visual highlight

With the integrated card holder you always have the time in view

A small extra pocket allows you to stow small items

Can also be fitted in combination with the PHDS-handlebar support

Already mandatory in many competitions

Provides optimum protection

Visual highlight

Can also be fitted in combination with the PHDS-handlebar support

Can only be fitted in combination with handlebar support 5900103920001S (standard on EXC models up to MY 2011)

These CNC-machined, high-strength aluminium handlebar risers are extremely robust thanks to their special screw fastening (from below) on the triple clamp

Twisting and bending are therefore practically impossible

Use of these handlebar risers is only possible on CNC-machined triple clamps

Available in three different heights

Improves clutch performance and durability

Hinson-typical surface treatment for significantly improved robustness compared to the standard part

Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled

Can be installed in the standard clutch or in combination with other Hinson clutch components

CNC milled from high-strength aluminium

Improves heat dissipation

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

The current rpm from 0-19,999 can also be displayed

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

4 pieces 37mm x 31mm

4 pieces 48mm x 40mm

Ignition curve adjustment made easy!

Comfortable ignition curve adjustment on the handlebar

All parts required to install the kick-starter system on your motorcycle

Combination of kick and electric starter system > maximum starting safety

 Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280kg

With handlebar loops

With rubberized hooks on belt ends

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280 kg

With handlebar loops

Perfect for extending lashing straps with hooks or carabiners

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280kg

With handlebar loops

With rubberised hooks and carabiner on belt ends

Left hand side fairing

Tool for lifting the motorcycle

Secure stand for your bike

Stroke: 315/425mm

Maximum load: 150kg

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Made of the highest quality materials

Tested in the toughest conditions

Developed together with the vehicle

Enables shorter drivers to also achieve the optimum seat height

Perfect compromise between maximum chassis performance and lowest possible vehicle height

No restrictions on riding dynamics

Lower section of air filter

Made of the highest quality materials

Tested in the toughest conditions

Developed together with the vehicle

Enables shorter drivers to also achieve the optimum seat height

Perfect compromise between maximum chassis performance and lowest possible vehicle height

No restrictions on riding dynamics

Can be mounted without additional mounting material

Welded seams

Robust and waterproof bag

Waterproof roll closure

Resistant waterproof coating

Increases the volume of the rear master cylinder

Additional cooling ribs minimise the heating of the brake fluid

Eliminates “fading” almost completely

Total height including cover approximately 26.5mm

Secure stand for your bike

Aluminium construction with non-slip underlay so the motorcycle does not slip during washing