Products

With scaling for both the fluid level and different mixture ratios

Perfect for changing the oil and for preparing larger quantities of 2-stroke mixture in the canister

Simple handling thanks to the ergonomic design

Air filter box front part

Left hand air filter cover

Protects the intake system against water and dirt when cleaning the air filter box

Acts as an additional protective layer

Recommended for extremely dusty conditions

Premature sanding of the air filter is avoided

Coarse-pored air filter cover

Right hand air filter panel

Optimised air flow

Optimised air flow

Left hand

Recommended for extremely dusty conditions

Recommended in extremely wet conditions

Additional protection against water splashes and sludge

For extremely muddy conditions

Developed according to the requirements of our factory drivers

Reduced weight

Self adhesive special foam, prevents mud and dirt from sticking to your plastics and in this way prevents your bike from gaining weight during riding in muddy conditions

Enables power consumers such as grip heater or radiator fans to be installed on motocross or cross-country models as well

The power consumer is now connected directly to the battery

Consequently, the battery is also drained when the engine is not running, unless the consumer is switched off

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

With return valve

Anodised dust protection cap

Quick and easy bleeding of the brake

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

With return valve

Anodised dust protection cap

Quick and easy bleeding of the brake

High stiffness and strength

Made of high-quality carbon

Optimal protection against stone impact

Visual highlight

Optimal protection against stone impact

Can be installed on brake caliper supports 77713975044, 79613975044, 7771397501030, 7771397511030, 78113975044, 78113975144, 78113975244, 78913975044 or 78913975144

Made of high-strength aluminium

Improved braking performance

Only for Brembo brake systems

Required for using the 320 mm brake disc 58309060000 with Brembo brake caliper

Made of high-strength aluminium

Improved braking performance

Required for using a 270 mm brake disc and 2-piston Brembo brake caliper

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Only mountable with Brembo brake system

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Made of high-quality carbon

Protects the rear brake disc from stones and other solid obstacles

Can be fitted on the CNC brake calliper support 77713975044 or 7771397511030 or 7251397500030

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Adjustable grip width

Practical help when loading the bike or jacking up with the rear wheel lifting device

Softer due to high content of organic substances

Thermal insulation by means of ceramic underlayer

Less aggressive brake feel

Lower friction coefficient than sintered brake pads

Special material mixture

Practical tool for setting preload on the shock absorber without having to remove it

Practical tool for setting preload on the shock absorber