Products

AIR FILTER BOX FRONT PART

AIR FILTER BOX FRONT PART

AIR FILTER BOX FRONT PART

AIR FILTER BOX FRONT PART

Protects the intake system against water and dirt when cleaning the air filter box

Acts as an additional protective layer

Recommended for extremely dusty conditions

Premature sanding of the air filter is avoided

Coarse-pored air filter cover

Washable

AIR FILTER PANEL

AIR FILTER PANEL

AIR FILTER PANEL

Recommended for extremely dusty conditions

Acts as an additional protective layer

Extends the filter service intervals

Premature sanding of the air filter is avoided

Recommended in extremely wet conditions

Acts as an additional protective layer

Washable

Substantial weight saving

Increased tightening torque

Increased performance

More usable speed range

Better power delivery

Improved handling overall due to finer dosing capacity on the throttle grip

Sensitive response

Rich sound

Manifold routing optimally adapted to the production engine

Complies with current FIM noise regulations

Complies with current AMA noise regulations

Manufactured entirely from high-grade titanium

Increased tightening torque

Increased performance

More usable speed range

Better power delivery

Improved handling overall due to finer dosing capacity on the throttle grip

Sensitive response

Rich sound

Manifold routing optimally adapted to the production engine

Stainless steel header

Silencer housing made of high-grade titanium

Complies with current FIM noise regulations

Complies with current AMA noise regulations

Made from high grade titanium

Uncompromising race look

Permanently welded brackets

Complies with current FIM noise regulations

Significantly more performance

Substantial weight saving

Enables power consumers such as grip heater or radiator fans to be installed on motocross or cross-country models as well

The power consumer is now connected directly to the battery

Consequently, the battery is also drained when the engine is not running, unless the consumer is switched off

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

With return valve

Anodised dust protection cap

Quick and easy bleeding of the brake

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

With return valve

Anodised dust protection cap

Quick and easy bleeding of the brake

Made of high-strength aluminium

Improved braking performance

Only for Brembo brake systems

Required for using the 320 mm brake disc 58309060000 with Brembo brake caliper

Made of high-strength aluminium

Improved braking performance

Required for using a 270 mm brake disc and 2-piston Brembo brake caliper

High stiffness and strength

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Manufactured using state-of-the-art 2-component injection moulding technology

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tyre changes, brake service etc. without removing the brake cover

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Adjustable grip width

Softer due to high content of organic substances

Thermal insulation by means of ceramic underlayer

Less aggressive brake feel

Lower friction coefficient than sintered brake pads

Special material mixture

Perfect for all on the move

Exceptionally robust

Note

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Visual highlight

Race look

Visual highlight

Perfect for changing the look of your motorcycle

Elegant look