Products

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 999

Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall

)Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

Comfortable unhooking of springs

Convenient and easy to use

Easy handling and operation

13cm tall, 3 pieces each

13cm tall, 3 pieces each

Teeth made of high-strength steel, for an extra long service life

Aluminium centre section, reduces unsprung masses

Permanently joined together with high-strength rivets

At least three times longer service life than other aluminium rear sprockets

50% lighter than steel rear sprockets

Longer service life of the entire drivetrain kit

Sprockets with different teeth number as stock are CCCUO_EU!

Makes it easier to stand your motorcycle up

Specially developed for extreme conditions

Strap made from high-strength nylon

Permanent protection against unattractive scratches and matte spots on the swingarm

Protects from damage in the event of a fall

Colour differences between the upper and lower triple clamp cannot be technically ruled out

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Optimally tuned steering stem stiffness

100% alignment of the fork tubesIdeal flexibility – precisely customised to the WP fork

Including steering stem with steering head bearing already pressed on

Required items for installation on SX models from model year 2016:

Handlebar mount kit 78901939044/144/244/344/444 or

PHDS SXS07125200

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

Colour differences between the upper and lower triple clamp cannot be technically ruled out

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Optimally tuned steering stem stiffness

100% alignment of the fork tubes

Ideal flexibility – precisely customised to the WP fork

Including steering stem with steering head bearing already pressed on

Required items for installation on SX models from model year 2016:

Handlebar mount kit 78901939044/144/244/344/444 or

PHDS SXS07125200

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

There's racing experience here as well!

Practical tyre lever set, consisting of 3 x short version 51012092100 and 3 x long version 51012093100

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Made of robust plastic

Fastening independent of fittings directly on the handlebars

To convert the open, standard handguards to a closed version

Made of robust plastic

Fastening independent of fittings directly on the handlebars

To convert the open, standard handguards to a closed version

Greater flexibility and better running characteristics

Constant and permanent lubrication

Better sealing against water and dirt

Significantly longer durability