450 SMR 2025

With scaling for both the fluid level and different mixture ratios

Perfect for changing the oil and for preparing larger quantities of 2-stroke mixture in the canister

Simple handling thanks to the ergonomic design

Enables power consumers such as grip heater or radiator fans to be installed on motocross or cross-country models as well

The power consumer is now connected directly to the battery

Consequently, the battery is also drained when the engine is not running, unless the consumer is switched off

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Specially developed for LiFePo4-batteries

Voltages 13.2 V

Charging current - 2.5 amps

Optimizes battery performance and service life

Recovery mode for low battery voltage

Precise battery monitoring

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Made of high-quality carbon

Protects the rear brake disc from stones and other solid obstacles

Can be fitted on the CNC brake calliper support 77713975044 or 7771397511030 or 7251397500030

Practical help when loading the bike or jacking up with the rear wheel lifting device

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Visual highlight

Race look

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Including plastic insert

Reduces the risk of a lever being broken

Suitable for all Brembo® and Formula brake and clutch assembles

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

100mm length

20 blades: 0.05 - 0.1 - 0.15 - 0.2 - 0.25 - 0.3- 0.35 - 0.4 - 0.45 - 0.5 - 0.55 - 0.6 - 0.65 - 0.7 - 0.75 - 0.8 - 0.85 - 0.9 - 0.95 - 1.0mm

Contents are in accordance with DIN standard 13167-2014 for motorcyclists

Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain

Protects the radiator from mud, dirt and sand

Protection against rapid overheating of the engine in muddy conditions

For extremely muddy conditions

Reduces dirt deposits between engine and skid plate

Provides better cooling of the engine

Small and light, so very portable - saves the day in the event of a puncture on the move!

Mini-foot pump with pressure gauge on the swivelling valve head that fits all prevalent valves

Integrated double-cylinder with pressure switch-over to high pressure

Maximum 12 bar

Height: approximately 170mm folded together

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Wider contact surface than standard:

+8mm at 125/150 SX/XC-W, SX-F, 450/500 EXC-F

+16mm at 250/300 SX/EXC, 250/350 EXC-F

Stabilises the motorcycle during transport

Protects the fork shaft sealing rings and fork springs against damage due to tension belts being tightened too much

Is clamped between the bottom of the front fender and tyre

Funnel specially developed for KTM motorcycles

Diameter (small and large) optimized to suit the filler neck; special groove for optimum ventilation

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

6mm wider contact surface than standard

Coated neoprene ring

Simply pulled over the grips

Optimum protection against blisters on the thumbs with these coated neoprene rings

Prevents dirty grips

Developed according to the requirements of our factory drivers

Less stress when riding

Objective: comfort AND safety

Ergonomic contour adapted to the shape of the hand for maximum comfort

Half waffle grip

For a secure grip

Three areas for the metal wire locking

Version: medium

Developed according to the requirements of our factory drivers

Less stress when riding

Objective: comfort AND safety

Ergonomic contour adapted to the shape of the hand for maximum comfort

Half waffle grip

For a secure grip

Three areas for the metal wire locking

Version: soft

Closed design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Available in two different heights

Improved optics

Low version

Closed design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Available in two different heights

Improved optics

High version

Maximum protection against falls, flying stones, branches, etc

Indispensable companion for heavy off-road and Supermoto use

Wide, generous design in combination with sturdy aluminium bracket

Prevents broken levers

Made of robust plastic

Maximum protection against falls, flying stones, branches, etc

Indispensable companion for heavy off-road and Supermoto use

Wide, generous design in combination with sturdy aluminium bracket

Prevents broken levers

Made of robust plastic

Maximum protection against falls, flying stones, branches, etc

Indispensable companion for heavy off-road and Supermoto use

Wide, generous design in combination with sturdy aluminium bracket

Prevents broken levers

Made of robust plastic

Excellent weather protection