450 SMR 2025

With scaling for both the fluid level and different mixture ratios

Perfect for changing the oil and for preparing larger quantities of 2-stroke mixture in the canister

Simple handling thanks to the ergonomic design

Enables power consumers such as grip heater or radiator fans to be installed on motocross or cross-country models as well

The power consumer is now connected directly to the battery

Consequently, the battery is also drained when the engine is not running, unless the consumer is switched off

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

With return valve

Anodised dust protection cap

Quick and easy bleeding of the brake

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Specially developed for LiFePo4-batteries

Voltages 13.2 V

Charging current - 2.5 amps

Optimizes battery performance and service life

Recovery mode for low battery voltage

Precise battery monitoring

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

With return valve

Anodised dust protection cap

Quick and easy bleeding of the brake

High stiffness and strength

Made of high-quality carbon

Optimal protection against stone impact

Visual highlight

Optimal protection against stone impact

Can be installed on brake caliper supports 77713975044, 79613975044, 7771397501030, 7771397511030, 78113975044, 78113975144, 78113975244, 78913975044 or 78913975144

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Only mountable with Brembo brake system

Made of high-quality carbon

Protects the rear brake disc from stones and other solid obstacles

Can be fitted on the CNC brake calliper support 77713975044 or 7771397511030 or 7251397500030

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Practical help when loading the bike or jacking up with the rear wheel lifting device

Practical tool for setting preload on the shock absorber

Perfect for all on the move

Exceptionally robust

Note

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Specially developed for use in motocross

No O- or Z-rings > minimum loss of power and good durability

Made of high-strength aluminium

Protects the chain guide bracket from major damage

Visual highlight

Race look

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Including plastic insert

Reduces the risk of a lever being broken

Suitable for all Brembo® and Formula brake and clutch assembles

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Ergonomically perfect shape (the result of years of racing experience)

Adjustable grip width

Suitable for all hydraulic Brembo® clutch mountings

Protects from damage in the event of a fall

Easy to mount

Protects the fork

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

Highest quality workmanship

The right combination of look, style, and performance

Specially designed for the challenges of off-road use

Made from special, high-strength plastic for maximum stability

With exchangeable chain track surface, therefore extremely durable

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

CNC milled from high-strength aluminium

Not lockable

Extremely fast and keyless refuelling

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Clear pressure point across the entire temperature range

More brake power

Higher stiffness with the same weight

Made of high-strength aluminium

Race look

Visual highlight

With exchangeable chain track surface, therefore extremely durable

Specially designed for the challenges of off-road use

CNC machined out of teflon