450 EXC-F SIX DAYS 2021

4 pieces 37mm x 31mm

4 pieces 48mm x 40mm

13cm tall, 3 pieces each

13cm tall, 3 pieces each

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

High-end steering damper

Maximum control on fast tracks

Gain in stability at the front wheel

Fully adjustable

Well thought-out mounting of the damper enables individual handlebar adjustment

Reduced weight

Sensitive response behaviour

High speed DCC

Developed according to the requirements of our factory drivers

Optimum 25 click setting range

Proven success with the KTM Works Rally Team

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

Installed in the standard clutch, which means simple, uncomplicated and fast installation

Unlimited and total concentration on the perfect line

New generation of Rekluse centrifugal clutch with EXP technology

Easily adjustable from the outside via the clutch slave cylinder

No stalling of the engine in critical situations, such as braking, downhill runs, jumping, or when starting or pushing

Improved traction, controllable by the throttle alone

Slippery, extremely steep sections can be managed more easily > saves time and ensures faster lap times

More relaxed, fatigue-free and controlled riding, even over longer distances and in tough terrain

No more coupling is required, although it is still possible

Special rear brake conversion kit available, allowing braking of the rear wheel with the left hand

Tested in the toughest conditions

Protects the intake system against water and dirt when cleaning the air filter box

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280 kg

With handlebar loops

Perfect for extending lashing straps with hooks or carabiners

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall

)Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

Left hand side fairing

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 999

Dimensions: A = 104 mm, B = 811 mm, C = 74 mm

Highest quality workmanship

Including straps

It withstands a load of 180 kg

The total length is approximately 200cm, folded approximately 100cm

Clear pressure point across the entire temperature range

More brake power

Higher stiffness with the same weight

Made of high-strength aluminium

Specially developed for LiFePo4-batteries

Voltages 13.2 V

Charging current - 2.5 amps

Optimizes battery performance and service life

Recovery mode for low battery voltage

Precise battery monitoring

Easy readable display for easy monitoring of operating hours up to 99,999 total hours

The current rpm from 0-19,999 can also be displayed

With the supplied double-sided adhesive tape, easy installation is guaranteed, screwing is also possible

Specially designed for the challenges of off-road use

Significantly longer durability

Made of high-strength aluminium

The right combination of look, style, and performance

The lightest Renthal Sprocket on the market

Provide maximum power transfer and long-life due to advanced tooth profile and perfect concentricity

Combination of a high strength base material and exceptionally hardwearing surface

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Protects the frame without changing the slim lines of your motorcycle

Provides maximum protection at the lowest possible weight

Easy to mount

Optimal protection against stone impact

Visual highlight

Suitable for the left and right side

Suitable for the left and right side

Provides maximum protection at the lowest possible weight

Optimal protection against stone impact

Easy to mount

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Spoiler set

SPOILER SET

FRONT NUMBER PLATE

Optimised air flow

Right hand air filter panel

Air filter box front part

Fork protector kit