450 EXC-F SIX DAYS 2021

Made of high-strength aluminium

Improved braking performance

Required for using a 270 mm brake disc and 2-piston Brembo brake caliper

Already mandatory in many competitions

Provides optimum protection

Visual highlight

With the integrated card holder you always have the time in view

A small extra pocket allows you to stow small items

Can also be fitted in combination with the PHDS-handlebar support

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Acts as an additional protective layer

Recommended for extremely dusty conditions

Premature sanding of the air filter is avoided

Coarse-pored air filter cover

Recommended for extremely dusty conditions

Particularly safe due to clever design

Clutch is secured by simply twisting the connection

Keeps water out of the silencer during cleaning

For internal diameters 37 mm - 62 mm

To prevent the ingress of water in the silencer when cleaning

For inner diameters 15 mm - 38 mm

Increases the volume of the rear master cylinder

Additional cooling ribs minimise the heating of the brake fluid

Eliminates “fading” almost completely

Total height including cover approximately 26.5mm

To ensure the sensor magnet is in the correct location even after a change from Enduro to Supermoto wheels

Sensor magnet 58214050054 is required

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

WRAP-AROUND HANDGUARD KIT

Resistant coating

Higher compared to the standard seat

Specially designed for riders with a height of above 1.80m

Resistant coating

Higher compared to the standard seat

Specially designed for riders with a height of above 1.90m

Elegant cover

Resistant coating

Plenty of freedom of movement and yet perfect hold

The “Wave surface” has the effect of a gradation

Same seat height like the standard seat

Developed according to the requirements of our factory drivers

Resistant coating

Special gradation for good grip even when accelerating hard

Standard seat height

Same seat height like the standard seat

Resistant coating

Highly elastic foam for extra comfort

Same seat height like the standard seat

Additional protection against water splashes and sludge

For extremely muddy conditions

Developed according to the requirements of our factory drivers

Reduced weight

Self adhesive special foam, prevents mud and dirt from sticking to your plastics and in this way prevents your bike from gaining weight during riding in muddy conditions

Recommended for storing your timecard during races

Stick it directly to the seat with grip glue

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Wider contact surface than standard:

+8mm at 125/150 SX/XC-W, SX-F, 450/500 EXC-F

+16mm at 250/300 SX/EXC, 250/350 EXC-F

Improves clutch performance and durability

Hinson-typical surface treatment for significantly improved robustness compared to the standard part

Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled

Can be installed in the standard clutch or in combination with other Hinson clutch components

CNC milled from high-strength aluminium

Improves heat dissipation

Protects the radiator from mud, dirt and sand

Protection against rapid overheating of the engine in muddy conditions

For extremely muddy conditions

Designed to completely change the original look of your motorcycle

Glue the graphics kit directly onto the standard fairing parts

Can be removed without leaving any residue

Made of the highest quality materials

Visual highlight

Perfect fit

Personalise the look of your motorcycle

Race look

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing rings

Made of the highest quality materials

Tested in the toughest conditions

Developed together with the vehicle

Enables shorter drivers to also achieve the optimum seat height

Perfect compromise between maximum chassis performance and lowest possible vehicle height

No restrictions on riding dynamics

Made of the highest quality materials

Tested in the toughest conditions

Developed together with the vehicle

Enables shorter drivers to also achieve the optimum seat height

Perfect compromise between maximum chassis performance and lowest possible vehicle height

No restrictions on riding dynamics

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Practical tool for setting preload on the shock absorber

Exceptionally robust

LED technology, specially developed for use with the Enduro

Very high light output

Light intensity 1500 lm

Light colour approx. 5,500 K

Can be installed in the standard headlight mask

Plug & Play mounting

On EXC and Freeride models, the LED light is switched on and off using the fade-in switch

This article is not available in Germany.

Provides maximum protection at the lowest possible weight

Including adapted radiator protection grills

Easy to mount

Optimal protection against stone impact

Coolant reservoir for overheated radiators

To be installed in the frame breast pipe

Toolless adjustment of the spring preload

Ergonomically perfect shape (the result of years of racing experience)

Without fuel tank cap

Comes with adapters for mounting your stock spoilers

Perfect fit

4 parts

Perfect fit

4 parts