450 EXC-F SIX DAYS 2021

Recommended for extremely dusty conditions

Keeps water out of the silencer during cleaning

For internal diameters 37 mm - 62 mm

To prevent the ingress of water in the silencer when cleaning

For inner diameters 15 mm - 38 mm

Increases the volume of the rear master cylinder

Additional cooling ribs minimise the heating of the brake fluid

Eliminates “fading” almost completely

Total height including cover approximately 26.5mm

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

WRAP-AROUND HANDGUARD KIT

Resistant coating

Higher compared to the standard seat

Specially designed for riders with a height of above 1.80m

Resistant coating

Higher compared to the standard seat

Specially designed for riders with a height of above 1.90m

Elegant cover

Resistant coating

Plenty of freedom of movement and yet perfect hold

The “Wave surface” has the effect of a gradation

Same seat height like the standard seat

Developed according to the requirements of our factory drivers

Resistant coating

Special gradation for good grip even when accelerating hard

Standard seat height

Same seat height like the standard seat

Resistant coating

Highly elastic foam for extra comfort

Same seat height like the standard seat

Additional protection against water splashes and sludge

For extremely muddy conditions

Developed according to the requirements of our factory drivers

Reduced weight

Self adhesive special foam, prevents mud and dirt from sticking to your plastics and in this way prevents your bike from gaining weight during riding in muddy conditions

100mm length

20 blades: 0.05 - 0.1 - 0.15 - 0.2 - 0.25 - 0.3- 0.35 - 0.4 - 0.45 - 0.5 - 0.55 - 0.6 - 0.65 - 0.7 - 0.75 - 0.8 - 0.85 - 0.9 - 0.95 - 1.0mm

Recommended for storing your timecard during races

Stick it directly to the seat with grip glue

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Wider contact surface than standard:

+8mm at 125/150 SX/XC-W, SX-F, 450/500 EXC-F

+16mm at 250/300 SX/EXC, 250/350 EXC-F

Improves clutch performance and durability

Hinson-typical surface treatment for significantly improved robustness compared to the standard part

Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled

Can be installed in the standard clutch or in combination with other Hinson clutch components

CNC milled from high-strength aluminium

Improves heat dissipation

Protects the radiator from mud, dirt and sand

Protection against rapid overheating of the engine in muddy conditions

For extremely muddy conditions

Designed to completely change the original look of your motorcycle

Glue the graphics kit directly onto the standard fairing parts

Can be removed without leaving any residue

Made of the highest quality materials

Visual highlight

Perfect fit

Personalise the look of your motorcycle

Race look

Practical tool for setting preload on the shock absorber

Provides maximum protection at the lowest possible weight

Including adapted radiator protection grills

Easy to mount

Optimal protection against stone impact

Perfect fit

4 parts

Perfect fit

4 parts

Specially developed for extreme conditions

Strap made from high-strength nylon

Makes it easier to stand your motorcycle up

Prevents dirty grips

Protects the radiator from mud, dirt and sand

Protection against rapid overheating of the engine in muddy conditions

For extremely muddy conditions

4 pieces 37mm x 31mm

4 pieces 48mm x 40mm

Colour differences between the upper and lower triple clamp cannot be technically ruled out

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Optimally tuned steering stem stiffness

100% alignment of the fork tubesIdeal flexibility – precisely customised to the WP fork

Including steering stem with steering head bearing already pressed on

Required items for installation on SX models from model year 2016:

Handlebar mount kit 78901939044/144/244/344/444 or

PHDS SXS07125200

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

Colour differences between the upper and lower triple clamp cannot be technically ruled out

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Optimally tuned steering stem stiffness

100% alignment of the fork tubes

Ideal flexibility – precisely customised to the WP fork

Including steering stem with steering head bearing already pressed on

Required items for installation on SX models from model year 2016:

Handlebar mount kit 78901939044/144/244/344/444 or

PHDS SXS07125200

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

13cm tall, 3 pieces each

13cm tall, 3 pieces each

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

High-end steering damper

Maximum control on fast tracks

Gain in stability at the front wheel

Fully adjustable

Well thought-out mounting of the damper enables individual handlebar adjustment

Reduced weight

Sensitive response behaviour

High speed DCC

Developed according to the requirements of our factory drivers

Optimum 25 click setting range

Proven success with the KTM Works Rally Team

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

For all 48mm forks

Made of high-quality carbon