450 EXC-F SIX DAYS 2021

Enables power consumers such as grip heater or radiator fans to be installed on motocross or cross-country models as well

The power consumer is now connected directly to the battery

Consequently, the battery is also drained when the engine is not running, unless the consumer is switched off

Closed design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Available in two different heights

Improved optics

Low version

With return valve

Anodised dust protection cap

Quick and easy bleeding of the brake

Magnetic

Never lose a bolt again!

Perfect for use in combination with the SX stand

Perfect for all 2-stroke riders on the move

The small bottle fits in your tool bag or jacket

Capacity 250 ml, with scaling for different mixture ratios (1:40 / 2.5%; 1:50 / 2%; 1:60 / 1.7%; 1:80 / 1.25%)

Transparent plastic canister including a flexible hose and screw cap

For legal reasons, not to be used in some countries for storage and transportation of gasoline

Tool for lifting the motorcycle

Secure stand for your bike

Stroke: 315/425mm

Maximum load: 150kg

Made of high-strength aluminium

Improved braking performance

Required for using a 270 mm brake disc and 2-piston Brembo brake caliper

Already mandatory in many competitions

Provides optimum protection

Visual highlight

With the integrated card holder you always have the time in view

A small extra pocket allows you to stow small items

Can also be fitted in combination with the PHDS-handlebar support

Keeps water out of the silencer during cleaning

For internal diameters 37 mm - 62 mm

To prevent the ingress of water in the silencer when cleaning

For inner diameters 15 mm - 38 mm

Increases the volume of the rear master cylinder

Additional cooling ribs minimise the heating of the brake fluid

Eliminates “fading” almost completely

Total height including cover approximately 26.5mm

Specially developed for WP forks

Fork bleeding using finger pressure

Developed together with the vehicle

DID YOU KNOW that all KTM CNC parts are manufactured from high grade aluminium, which not only looks great but can also stand up to the toughest loads?

The original factory look, anodized aluminium PowerParts are just the thing to give your KTM that something special

WRAP-AROUND HANDGUARD KIT

100mm length

20 blades: 0.05 - 0.1 - 0.15 - 0.2 - 0.25 - 0.3- 0.35 - 0.4 - 0.45 - 0.5 - 0.55 - 0.6 - 0.65 - 0.7 - 0.75 - 0.8 - 0.85 - 0.9 - 0.95 - 1.0mm

Recommended for storing your timecard during races

Stick it directly to the seat with grip glue

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Wider contact surface than standard:

+8mm at 125/150 SX/XC-W, SX-F, 450/500 EXC-F

+16mm at 250/300 SX/EXC, 250/350 EXC-F

Improves clutch performance and durability

Hinson-typical surface treatment for significantly improved robustness compared to the standard part

Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled

Can be installed in the standard clutch or in combination with other Hinson clutch components

CNC milled from high-strength aluminium

Improves heat dissipation

Practical tool for setting preload on the shock absorber

Use highly recommended when washing the bike thoroughly; in other words, when the fuel tank is removed

Prevents water from entering the fuel line

Prevents dirty grips

Protects the radiator from mud, dirt and sand

Protection against rapid overheating of the engine in muddy conditions

For extremely muddy conditions

4 pieces 37mm x 31mm

4 pieces 48mm x 40mm

13cm tall, 3 pieces each

13cm tall, 3 pieces each

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

For all 48mm forks

Made of high-quality carbon

For tank and carburetor bleeding

Gasoline resistant

Can only be used for bleeding purposes

Cannot be used as a connection between tank and carburetor!

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280 kg

With handlebar loops

Perfect for extending lashing straps with hooks or carabiners

The Twinwall, in the KTM orange design

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall

)Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

Two handlebars in one

The exterior ensures maximum resistance to external damage (e.g. fall)

Additionally hard anodised against corrosion

The interior, made of a special alloy, is also hard anodised to protect it from damage by the handlebar controls

Nylon inserts in the inner tube allow thinner walls

Very good flex properties

Comes with handlebar pad

Renthal Twinwall 996

Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight